Reasons Why Your Nissan Qashqai Key Fob Won't Work

The Qashqai has a distinct SUV feel to it thanks to its larger dimensions. Moreover, the wheel sizes of 19 inches in Ti and ST-L models may be a bit stiff at times. The front tyres may lose grip on rough surfaces, and its CVT can occasionally display wrist-flexing torque steer.

This is usually caused by dead batteries that can be replaced in just a few minutes. Be sure that the replacement battery is of the same voltage, size, and specification.

Water Damage

One of the most common reasons why a Nissan key fob gives the "key ID is incorrect" message is due to water damage. The rubber seals on the key fob are designed to protect the chip's electronic components, however prolonged moisture exposure can you reprogram a nissan key fob cause it not to work correctly. It's normal to see this if your key fob has been dropped in the ocean or in a pool. However, it can occur when it becomes wet from showers or soapy hands.

If your key fob is exposed to water for a long period of time, it might need to be cleaned with isopropyl alcohol or electronic cleaner. In addition, it may need to be taken to a specialist to repair or replace it.

If your key fob needs to be replaced, it's a relatively simple procedure. First, make sure you have a multipack of the right battery (CR2032 3V). Open the front and rear cases using a flathead screwdriver. You'll need to take out the clips that hold the metal together and push out the old battery, and then put in the new one. After reassembling the fob put the mechanical key back into place and verify that it works as expected. If it isn't, you will need to take it to your local Nissan dealer or an expert auto locksmith to fix the chip in the key. The chip isn't usually damaged by water so it shouldn't be too expensive.

Dead Coin Battery

Another reason why your Nissan Qashqai key fob may not work is that the battery in the coin has gone dead. These batteries usually last 3-5 years, but they may fail over time, especially if the fob is dropped frequently. You can replace the battery with a new one but be sure it's the same voltage and size as the original. If you replace the battery, it could cause the key to be assigned an incorrect key ID. This will stop it from being paired with your vehicle.

The best way to replace the coin battery on a Nissan Qashqai key fob is by prying open the key fob using an small screwdriver that has a flat head. Push in the screwdriver in a small notch at the bottom of the fob and turn it around gently to separate the two halves of the key fob. Remove the old CR2025 battery and replace it with a brand new one, noting the position of the old one within the fob.

Check the terminals for any dirt or water damage prior to installing the new battery. If this is the case, clean the terminals using some isopropyl ethanol. Make sure that the pole cables are properly connected. They must be connected to the negative and the positive poles of your battery.

Fault Diagnosis

If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water it could be an indication of an internal chip problem. You'll need a new keyfob in the event that you can't solve the issue by replacing the battery. If the key fob stopped working after you dropped it, it is likely that the chip inside was damaged. If you clean the chip using isopropyl ethanol and a paper towel and then insert it into the key fob, you can typically get it working again.

A common error that you may notice on your dashboard is "Key ID Incorrect." This means that the car cannot recognize the key fob and not allow it how to get a new key fob for nissan start the engine. The issue can be caused by a variety of things such as water damage, undetectable problems in the circuitry of the key fob or RFID interference.

The key fob will stop working in the event that the 12 volt batteries are dead or don't provide enough electrical current. This will affect your Nissan Qashqai's keyless system, central locking and the ability to start the engine with the key fob. If you are unable to lock or unlock the door manually you must check the batteries on your key fob to make sure they're in good shape. Try re-inserting the battery to reset the transmitter.

Reprogramming

If the key fob was not submerged into saltwater it should be able to return to life with a simple rinse of clean water. You can also clean the electronic chip with isopropyl or electronic cleaner. If none of these work it could be time to replace the entire key fob with an entirely new one.

If your Nissan Intelligent Key is still not working, it could be an issue with the connection between it and your car. Start by turning the ignition switch without starting the vehicle. Keep doing this until you see the warning lights flash twice. Then, turn the car off and take the keys out.

Next, open the fob compartment in your vehicle. It's usually on a door jamb, or the handle of the door for the driver. Find the small "program" button and press it. You should hear a chime sound after the process has been completed.

It's time to put your Intelligent Key to the test. Press all the buttons on the key while you are at a distance from the car. If the lights flash and the horn beeps, it means that the key has successfully connected to the Nissan. You may also try testing the key in close proximity.