UPVC Window Handle Replacement

It is easy to repair a damaged window handle with the right tools. But it's essential to know the type of handle and the spindle's length prior buying an alternative.

Older uPVC window handles have a spur that extends and is locked over the wedge striker. They can be left- or right-handed, and must be matched when replacing.

What type of lock and handle do I have?

There are a variety of windows locks and handles made of upvc, each with its particular advantages and uses. The type of handle you have will determine how easy it is to open your windows and whether or not the locking mechanism works according to the plan. Over time, and with regular use, the upvc handles on your windows can get worn out and damaged. This makes them less secure and less effective. In some instances they could even disappear completely. It is essential to fix your window handles made of upvc when you see them falling off. This will help prevent burglaries, and keep your house secure.

Luckily, replacing your window handles made of plastic is a simple task that is achievable by nearly anyone. You will need some basic tools, but with right knowledge, it is simple and should take only a couple of minutes. To get started you must identify the type of lock and handle that you have on your window made of upvc, which will help you find the perfect double glazing replacement windows.

Inline Espagnolette Handles

These are the most common type of upvc handles and are typically located on the other side of your window. They are flat and come with a latch which engages the locking mechanism of the window frame. Inline upvc handles come with a spindle running through the middle of the handle and into the window frame in order to control the latch.

Cockspur Handles

These handles are usually found on older uPVC window frames and have distinct hook-shaped designs. Cockspur handles are secured to the frame of the window with one screw, and are less secure than other kinds of window handle.

Handles that tilt and turn

The tilt and turn handles are different from other upvc handles because they can be turned to open the window and then tilted to the window to let air circulate. They have a 7mm spindle on the back and are available in left and right-handed versions.

It is crucial to determine the size of the spindle when purchasing a new upvc handles. Not all are the exact same size. Drop something in the middle of the hole to measure the length. This is the maximum spindle length that will fit in your window.

What is spindles?

uPVC window handles operate similarly as doors, with the user turning the handle to activate a latch inside the frame. The window then opens and closed. The handles can become damaged, particularly if they're used frequently or subjected to harsh conditions. This could mean that you have to replace your uPVC handles on windows since they may not be able to operate the window double glazing replacement properly for a long time.

There are many different types of uPVC handle options, such as Espag, Cockspur, and Spaded handles. These handles are designed to fit into the uPVC frames in various ways, and each type of handle utilizes a specific spindle to lock the mechanism fitted into the window. This is why it is crucial to know what kind of handle you have installed on your uPVC window so you can get the correct replacement for it.

You can find out what kind of uPVC handle you are using by looking at the base section of your handle. A snap-in covers should be over the screw that holds the base of the handle in place. Take it off and you should be able see the second screw at the opposite end of the base portion of the handle. After both screws are removed you should be in a position to pull the handle away from the uPVC window.

Once you have removed your uPVC window handle, you have to remove the old spindle from the locking mechanism. Note the length of the spindle. You will need to purchase a new one that is the same length as the original handle and the locking device.

The spindle wears out and becomes inoperable with the locking mechanism. This can be due to wear and tear from continuous use or loosening of the locking mechanism, or even corrosion that occurs over time. If this happens, you'll need to replace both the window handle and the locking mechanism in order to restore the full functionality of your uPVC Windows.

How do I remove the old handle?

Window handles are susceptible to being damaged or broken over time. It is important to fix them as soon as possible to ensure your safety. The good news is that replacing a damaged or worn handle is a relatively easy task that can be accomplished in less than an hour and doesn't require any specialist tools.

The first step in removing the handle that was previously used is to take off the screw situated at the top of the handle base. Once the screw is removed, the handle will be pulled away from the base section. Another screw will be located at the base of the handle. This can also be removed. Once the two screws are removed, the handle can be removed from the window's base.

After the handle has been removed, take the new handle and line up the fixing holes with the holes currently in the window frame. If there is a sticker or cap on the new handle remove it if needed and screw the handle in the appropriate position. Once the handle is in place, it is essential to check whether it functions by turning the handle and ensuring that the lock mechanism activates.

Espag handles feature spindles that extend out of the handle and slot into the multipoint locking mechanism that is on the frame of the window. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism, while Cockspur handles have an extended nose that hangs over either the frame's outer or transom bar cross member in the window.

Once you have the new handle in place, slide the spindle into the window lock and then tighten it down. When the handle is fixed in place, replace the'snap in' cover and screw cap (if necessary). The handle is now ready to use to use, so try opening and closing the window a few times to check that it functions properly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The process is easy. You only need a screwdriver and a bit of patience. First, make sure that the handle is not locked. Then, remove any visible screws. You can also replace them using screw caps. After removing the handle you'll need to take note of the length of the spindle which extends from the back. This is important as it will determine the kind of handle you'll need to buy.

Espagnolette handles made of uPVC are the most well-known kind of handle. They have a spindle that is inserted into the handle and acts as a locking mechanism within the frame of the window. The handle releases the latch and allows the window to open. With time and regular use, espagnolette handles could be damaged or damaged which is why it is essential to locate an alternative.

Cadenza handles are a form of uPVC handle that is commonly used in tilt and turn windows. They feature a protruding knife that works with a multiple-point locking mechanism within the window. They are generally more secure than handles made of espagnolette because they can only be opened from the inside. They can be replaced with the same method as espagnolette handles, however you must make sure that the new handle has an angled blade instead of a flat one.

Once you have decided on the right handle for you then you can line up the new handle with the screw holes, and then screw it into the appropriate position. Then, you should put the screw covers on and test your new handle. You can do this by dragging the handle between the locked position to the unlocked one a few time. If you experience any issues, it may be worth contacting a specialist to see if they can help resolve the problem. They are often able to advise you on the best way to solve the issue in a quick and effective manner.