Reasons Your fiat 500 abarth key 500 Key Fob Won't Work

A key fob from fiat 500 replacement key cost 500 is a convenient method to unlock the doors and get started the car. There are many reasons the fob won't work. It could be due to a dead battery or damaged receiver module, water damage problems, and interference.

This listing is for an NEW replacement Fiat Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most common reason your 500 key fob won't function is due to the battery is dead. Modern key fobs come with a limited operating range and should be within a few feet of the car to operate. If you're far from your car and hit the keyfob, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a brand new one from a reputable brand like Panasonic, Duracell, or Energizer. You can find them at your local hardware store, or on the internet.

You can test the coin-cell battery by pressing the buttons while you are standing close to your Fiat 500. The parking lights should light up and the key fob should operate the lock and unlock switches.

If your key fob still isn't working after replacing the battery, it may be water damage which hinders it from communicating with the module inside your vehicle. Water damage can happen in a variety of ways, such as the simple splash or submerging the key fob in saltwater at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture back out. If this does not work, you'll require your fob to be changed by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the circuit board of the fob and can cause it to short out and eventually end up dying. It's not good to get the fob wet but don't give up if you accidentally drop it in water or forget to take it out of your pants pocket.

First, remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Next check the fob to test if it works. If the fob doesn't work, it might need to be reprogrammed. This is usually done by an auto locksmith or dealer.

If the key is older and has never been programmed to your vehicle, it will likely need to be replaced completely. This is an easy process that can be carried out by a professional locksmith for automotive use. The locksmith will need the key to be cut to match the car's ignition. The locksmith will also need to reprogram the fob into the vehicle's system. This is a fast and affordable process that is usually completed within the next day.

Receiver Module Issues

One of the simplest reasons your 500 key fob may stop working is that it's simply out of range. The remote typically has 30 feet of range or less, and if it's too far away from your car it will not respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If your fob doesn't work after you replace the coin battery, also called a "button", "watch" or "button" It could be due to a problem with the internal circuit board. locked keys in car boot fiat punto the majority of cases, reprogramming your fob will fix the issue. You can find the instructions for most vehicles on YouTube or in the owner's manual.

It is possible to replace the metal retaining clips that hold the coin battery in place. If they lose tension it could prevent the battery from being seated properly and can cause your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of software or hardware problems. This can cause a major issue, but you are able to often fix this by visiting an auto locksmith to reprogram your fob. In certain instances the software may require reinstallation to your body control modules.

Interference

Interference can also cause the key fob to be unable to receive or transmit a signal. This can occur when the keyfob is located in close proximity to a radio transmitter like a cell phone or radar detector. Other reasons the key fob could not function include a poor connection to the buttons, damage to the internal chip or water damage.

If the key fob been unable to function for a while suddenly or after trying everything you can do at home to resolve it e.g. battery replacement, reprogramming and using the spare key fob, you might have a faulty receiver module on your 500. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands, which are then interpreted by the vehicle.

There is a simple way to reset the 500's on-board system including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by removing the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer of your lost car key fiat (sciencewiki.science). This will help you get your key fob working again. If the problem persists you should speak with an expert technician. They can identify the root of any problems.