Car Key Button Repair

A broken car key fob repairs key button is frustrating. It is possible to contact a 24-hour locksmith Service for help or purchase a new remote.

But, you may be able to save money by repairing a worn-out key fob rather than replacing it. This is especially true if the problem is caused by an old switch or a damaged contact.

Battery

If the buttons on your key fob aren't responding to pressing the buttons, this could be a clear indication that the battery is dying or at the end of its lifespan. Fortunately replacing the battery is an easy task that you can complete by yourself rather than hiring a locksmith or dealer to do it for you.

Find the battery compartment first. It is typically located on the back of the key fob and may be hidden behind a slide-out cover or an access point that opens when you press the button. Once the compartment is exposed then you will find the small battery. It's usually the shape of an ordinary coin and is marked with an plus and minus symbol. Remove the old battery and replace it with a brand new one. Check that the plus and minus symbols are aligned correctly.

Once the battery is installed close the compartment and snap the two halves of the key fob. Before closing the door ensure that you align and snap the pieces into the correct position. Press any of the buttons to confirm that they work properly.

If your remote key fob ceases working after replacing the battery, it could be experiencing other issues that require a different form of repair. Dropping the fob into a pool of water can cause it to cease functioning. Alternatively, it might be suffering from an internal electrical failure or it may require to be deprogrammed by a locksmith or locksmith. Also, take a look at these common automotive troubleshooting methods to determine if your key fob is experiencing a different issue.

Switches

There are many kinds of switches found in the car key fob according to the year and model. The older style key has an embedded chip that can be seen inside the case. The newer keys work by sending signals to your car. The buttons on a key can be worn out or damaged due how to repair broken car key normal use, regardless of the model. This causes them to become difficult to press or even ineffective. If you press the button with force it could cause more damage. It could also stop the key from working in the future.

If your key doesn't appear to be working, you should first try changing the battery. If it doesn't work, you might have to clean your key's fob or re-adjust its switches. Because these tiny electronic switches spend a lot of time being tossed around and tangled, they are more likely to fail than the larger components of your key.

The switches are rubber-like, and they're coated with an electrically conducting film that can wear down over time. Fortunately, they're tiny and easy to replace. They're soldered on the circuit board, therefore you must carefully take them off without causing any damage to any other part of the circuit. Then, you can solder in the new ones and rebuild your key fob.

Avoid using your car key fob for more than a couple of hours at a time, and avoid leaving it visible. When you're not using your key, put it away in a safe place.

If the problem persists after you've cleaned the key fob replaced the battery and attempted to clean it, you may need to consult an expert locksmith. A professional locksmith can test the frequency of your key to determine whether it's still able communicate with your vehicle, open and replace micro switches, alter cases, and more.

Outer Case

Key fobs spend a lot of time jostled around and if the buttons aren't free to move upwards and downwards within the case, they may become stuck or even broken. If changing the battery or cleaning it with the help of a cotton swab or rubbing alcohol don't resolve the issue, taking off the case and inspecting might be necessary. If the contact points where to repair car key remote the buttons touch aren't fitting well or are worn out, adjusting them may be the only solution to correct the issue.

Rubber buttons get worn out over time. The rubber is stretched, nails gouge into it, and the buttons become difficult to press. This can cause the key to fail, and in this case it's time for an entirely new case or buttons. This repair involves taking apart your remote, locating the buttons on the board, then heating the solder, and then carefully remove them. New buttons are then attached to the circuit board. The case can be reassembled, and the horseshoe key blade piece can be inserted. The new buttons should be snugly fitted inside the case to avoid them falling out.

Inner Case

Over time the buttons on your key fob could be damaged or stuck because of the constant jolting and accidental pressing. Using metallic tape and a hole-punch, you can solve this issue in the event that your vehicle isn't at home and the key fob isn't working, allowing you to unlock the doors, but not start the engine. This simple fix can enable you to safely get back to your car and continue your journey.