How to Repair Bifold Door Top Roller Guide

If your bifold door is sticking, it's likely that they need some maintenance. You may need to clean, lubricate or adjust them. The problem may be caused by a loose screw on the top pivot or by the top guide roller.

This kit includes all the hardware required to bring your bi fold door repair near me-bi fold door repairs closet door to its optimal performance.

Remove the Door

Installing a set of internal bifold doors could appear to be a complicated and complicated task however, it's actually straightforward for a DIYer with a bit of experience. Getting the frame into position isn't the problem but the trick is getting the doors to fold and close smoothly and precisely. As bifold doors are complex machines, they could require some 'tuning' to continue functioning properly. This might be something as simple as tightening a screw or as complex as taking out the door and replacing the pivot pin or roller.

Most times you can fix these issues with a couple of basic adjustments without removing the doors. It is possible that your bifold doors are sagging, scraping the floor or bouncing off the track. The solution to these issues isn't a big deal, and with three easy steps the bifold doors will be back on track in no time.

One of the most common problems that internal bifold doors have to face is the tendency to slide out of alignment. This could be due to loose screws, holes on the anchor/pivots, or a misaligned bifold door. In most cases, you can correct this with a few easy adjustments, but if your door isn't moving at all, it may need to be removed and replaced.

You'll need to open the door using an screwdriver, and perhaps an plier pair to loosen any pivot pins that are tight. The screwdriver can be used to disengage any locking levers that are on the bottom bracket of the pivot and the pliers allow you to wiggle the pin to release it and then take it off.

Once the top roller has become loose, you should be able to raise the door and swivel it downward in order to lift it out of its pivot brackets and track. It is usually a simple procedure, but be cautious not to let the door hit the frame of the door. Then you can sand the edge of the door to make it smooth. You can then repaint it or finish it according to the requirements.

Take off the Roller Guide

This spring-loaded roller guide is mounted on the top of bifold doors to aid in smooth operation. It is designed to work with Kenna frames and can be fitted to the door's panel from 1 inch to 3/8 inches thick. It is made from steel, nylon and plastic components. It is able to replace a damaged guide.

Take out any screws that are holding the roller guide in place by using the screwdriver. Use your hands to slowly lift it off the frame. This may require some effort, so have someone else help you keep the door in place while you remove it.

After the guide has been removed, carefully cut through the remaining finish over the foot of the new guide using a sharp blade to cut it off from the rod blank. This will make it easier to remove and ensure that there is no damage to the new guide foot. The guide foot is extremely sharp, and it can cut or snag fingers.

You may have to use some force to get the guide off, but be careful not to break or chip the foot. After you've separated the guide from the rod blank, make sure to take out all of the threads and epoxy that remain where it was affixed. This will help prevent any future issues with the guide.

After removing the old guide, try out your replacement by placing it in its place and then applying a few rotations of masking tape or some type of guide tubing to secure it in its place. This will allow you to double check the guide alignment and spacing to make sure everything is set up correctly. This is vital to avoid future problems regardless of whether you use the CRB Spine Finder and Deflection System or just eyeball it.

The last step is to replace the door. If the guide is in the proper position and functions in the correct way, then you're ready to proceed. Be aware that any screws or pins you removed or loosened should be replaced and tightened properly when you're done.

Remove the Bottom Pivot

Bifold doors can be an attractive addition to any home, but they often need to be tweaked or adjusted to keep them in good condition. Some issues can be addressed with the doors in place. Others will require that the doors be removed. This guide will demonstrate how to remove the internal bifold door glass replacement door pins, rollers and pivots.

Gathering your tools is the first step. You'll save yourself a lot of frustration by assembling all your tools in advance. You'll need a screwdriver pliers and perhaps a wrench. A set of basic tools can be purchased at a reasonable price from your local hardware store. It's important to keep some wood glue in your kit. This can be useful when you need to glue one rollers back into place.

Once you've got the tools, begin by opening the bifold doors and then loosening the top track bracket with your screwdriver. Once the bracket is in place, you should be able to lift the door off the top track. It may take a few jigglings but it should be able to pop right off the track.

The pivot at the bottom of the frame will need to be removed. Close all interior doors before you begin. This will be much easier than working from the inside. If the track at the bottom is in good shape it will be possible to lift the door and then remove the track.

You will need to replace the track if damaged. Hardware stores offer replacement tracks for bifold doors, as well as swinging closet doors. If the track is severely damaged then you may need to replace it entirely.

It is now time to check your doors for proper function. Make sure that the doors be moved into and out of their positions easily. Also, you should ensure that the edges of the door are parallel to the frame when it is closed. If they're not, you'll need to readjust the top pivot bracket and tighten or loosen the bottom setscrew until the door's edge coincides perfectly with the frame.

Replace the Roller

Bifold doors neatly enclose closets, laundry nooks and pantries, but only if they function properly. The bifold doors consist of two panels that are hinged and slide along tracks at the top of the frame. Over time the guides for the rollers can wear out and cause the doors to bow. The roller guide can be replaced in a matter of minutes with the use of basic tools.

The first step is to take the guide for the roller from the bi folding door repair panel. This requires removal of the bottom pivot bolt and loosening the screw that holds the guide to its top. After removing the guide, lift the panel from the track. Then, using a wrench, remove the top pivot bolt from the hole in the header of the frame by loosening the bolt.

A top nylon replacement guide with a 7/8 " diameter wheel and a base made of steel is available from Stanley, Cox or Acme. It is mounted on the top of the bifold door, which is 1 inch to 1-3/8 inches thick. It is spring loaded to self-adjust the upper track to ensure smooth sliding.

A bifold door can also scratch against the floor as it closes and opens. This can happen after adding carpet or other flooring materials that require that the doors be slightly raised to allow clearance. This issue can be fixed by getting rid of the screws that adjust the bottom pivot and loosening the top track mounting screws, and moving the anchor/pivot.

A set top roller with new guides can be an inexpensive solution to the problem of your bifold doors being difficult to operate. They're usually available at your local hardware store in the door section however, they are also available on the internet from a variety of suppliers. In addition to a new top guide for rollers, you'll require a small amount of Elmer's wood glue, which is sold in large box stores and a squeeze clamp. The clamp helps to hold the repair area in place after glue is inserted and allowed to dry.