Reasons Your fiat key programming Red key; pattern-wiki.win, 500 Key Fob Won't Work

A fiat remote key 500 key fob is a convenient way to unlock the doors and start the car. However, there are many reasons why the fob won't be working. This includes a dead coin-battery or water damage, receiver modules issues, and interference.

This listing is for an NEW replacement fiat key duplication Flip Key Remote - look-alike Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob that isn't working. Key fobs of today have an operating range that is limited and must be within just a few inches of the vehicle to function. If you are not within your car and press the keyfob button, it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a fresh one from a trusted brand such as Panasonic, Duracell, or Energizer. They are typically available in your local hardware store, or online.

After you've changed the battery on the coin cell You can test it by standing in front of your fiat key fob replacement 500 and pressing the buttons. The parking lights should light up and the key fob should operate the lock and unlock switch.

If the key fob won't function after replacing the battery, it could be damaged by water that blocks it from connecting to the receiver module in your car. Water damage can occur in a number of ways, from the slightest splash to submerging your fob in salt water at the beach. If you suspect your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If this isn't working, you'll need to have your fob reset by an auto locksmith or dealer.

Water Damage

While the fob comes with rubber seals that keep water out of the electronic chip inside the device, submerging it into the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short and then fail. The fob getting wet is not an option but if you accidentally drop it in an empty cup of water, or do not remember to take it out of your pants pocket before running the washer, don't give up hope.

First take the battery off the fob. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Check the fob again to check if it's working. If the key doesn't work, it may need to be reprogrammed. This is usually done by a dealer or professional auto locksmith.

If your key is a bit older and not programmed to work with your vehicle it is necessary to replace it completely. This is a simple procedure that can be completed by a professional automotive locksmith. The locksmith will require the key cut to match your car's ignition. They'll also have to reprogram the fob locked keys in car boot fiat punto the system of your car. This is a fast and inexpensive process that can usually be completed the same day.

Receiver Module Issues

One of the main reasons your 500 key fob might stop working is that it's simply out of range. The remote's range is of 30 feet, which means should you be too far from your car it won't be able to respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.

If your fob does not work after you replace the battery in the coin, also known as a "button", "watch" or "button" it could be due to a problem with the internal circuit board. Reprogramming the fob typically resolves the issue. You can find the steps for most vehicles on YouTube or in the owner's guide.

It is possible to replace the clips made of metal that hold the coin batteries in place. If they lose tension it can stop your coin battery from sitting properly and cause your remote to malfunction.

In rare instances, the fob can become out of sync with your vehicle because of hardware or software problems. This could cause a significant issue, but you are able to usually fix it by visiting a local dealer or auto locksmith to reprogram your fob. In some cases, the software may also require reinstallation in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit signals. This could happen if the key fob is close to the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. The key fob could not work due to a bad connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

There's a simple method to reset the 500's on-board system including the keyfob. Disconnect the battery for 15 minutes by taking off first the negative cable and then the positive cable. Reconnect the battery. This will remove any remaining electricity and then restart the car's computers. This can help you the key fob to function again. If the problem persists you should seek the advice of an expert technician. They can determine the root of your issues.